Service Manuals Testimonials Multimedia Editorials Archives Payments Sponsors Join Now! Advertise Contact Us Domains For Sale

The Laundromat Success Programâ„¢ helps you create a detailed plan to completely protect all aspects of your laundromat business.




Go Back   Coinwash The key to a successful Laundromat Business. > Questions / Support / Repair

Reply
 
Thread Tools
  #1  
Old 08-16-2006, 01:09 PM
Anonymous
"site-seer"
 
Posts: n/a
Default my speed queen top load washer error E:od

My electtronic control gives an error "e : od" about half way through the rinse cycel. What does this cone mean? any one know? thanks
Reply With Quote
  #2  
Old 08-16-2006, 01:39 PM
Coinwash's Avatar
Coinwash Coinwash is offline
Head Administrator
 
Join Date: Oct 1999
Location: NC / NY
Posts: 2,591
Default

is this what you wanted? oh yes can I have the model # Please

Quote:
Originally Posted by kbc747 View Post
The first page gives you the codes and what they stand for, the second page shows how to use them, use figure 6 to move within the program and make sure you follow the instructions to save your changes.
Hope this is what you were looking for, also if you want the part number for the book is 36198R7. If you want to set sale times etc you have to use a code let me know what you want and I will send you the code.


No water detected entering machine or Pressure switch trip not detected.

If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Or
If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.
Press PAUSE/CANCEL twice to clear the display.
• If there is no water in the unit:
1. Make sure that both valves at the water source(s) are turned on all the way.

2. Check for plugged or kinked inlet hoses or plugged screens in the inlet valves

3. Verify inlet valve operation

• If there is water in the unit:
1. Verify Drain pump operation

2. Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch

• Verify there is not a siphon problem

• Verify wire harness connections to:Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)

• Check all hoses for possible leaks

• Verify pressure switch operation

• Verify flow meter operation

• Verify CCU operation

F/02 Long Drain

If the drain time exceeds 8 minutes, the water valves are turned off and "F/02" is flashed.

NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.

Press PAUSE/CANCEL twice to clear the display.

• Check the drain hose and make sure it is not plugged or kinked.

• Check the electrical connections at the pump and make sure the pump is running.

• Check the drain pump filter for foreign objects.

• If the above does not correct the problem, replace the pump.

F/05 Water Temperature Sensor Error
If during the water heating step in wash cycle, the water temperature sensor (NTC) value is out of range, or the heating element circuit has failed, the "F/05" error code will be displayed.

• Check the Water Temperature Sensor, Heating Element and Element Relay

• Check connections to the Sensor, Heating Element and Relay

F/06 Drive Motor Tachometer Error

The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

• Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)

• Check the Drive Motor

• Check the MCU

• Check the Wire Harness

F/07 Motor Control Unit Error

The Central Control Unit has detected a short in the motor control unit. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.

•Check wire harness connections between the Drive Motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)

• Check the MCU

• Check the Drive Motor

• Check the Wire Harness

F/09 Overflow Condition

If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.


•Check the drain hose and make sure it is not plugged or inked.

• Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)

• Check/Clean Drain Pump Filter of foreign objects

• Check for Drain Pump Failure

• Check the Inlet Valve for proper shut off

• Check the Pressure switch for proper operation
F/10 Motor Control Unit (MCU) Heat Sink Thermal Trip
If the thermal protector on the MCU heat sink gets too hot, it will open the thermal protector on the heat sink which will stop motor functions and an "F/10" will be displayed.

•Check for Proper Installation, verify the unit is not located near a source of heat and has proper ventilation.

• Check Wire Harness connectors to the MCU, and Central Control Unit (CCU)

• Check the Drive system for any worn or failed components

• Check MCU

• Check Motor

F/11 Serial Communication Error

Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

•Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)

• Check the Drive system for any worn or failed components

• Check MCU

• Check CCU

• Check Motor

• Check Wire Harness

F/13 Dispenser Circuit Error
If the dispenser motor is not able to be driven to it's proper position.
• Check mechanical linkage from dispenser motor to the top of the dispenser.

• Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)

• Check Dispenser Motor

F/14 EEPROM Error
The Central Condrol Unit (CCU) receives it's data from an EEPROMonboard the CCU. If there is an error reading this data, it will cuse this error.

• A power glitch may cause this error. Try unplugging the Unit for two minutes to see if that fixes the error.

• Check CCU

F/15 Motor Control Unit (MCU) Error
If the MCU detects multiple resets or errors during a wash cycle, it will go into this error mode.

• Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)

• Check Drive belt

• Check MCU

• Check Motor

• Check Wire Harness

Sud SUDS LOCK (Overdose of Detergent detected during the Wash Cycle)

The motor control unit senses a suds lock condition by analyzing the current draw on the drive motor. If "Sud" is displayed a potential suds lock is detected. This may signify a bad pump, an extra heavy load, excessive detergent, or excessive suds.

• If too much detergent was used, run the unit through a Rinse/Spin cycle, then a Normal cycle, without adding any detergent. This should clear the unit of the excess detergent.

• Check the drain hose and make sure it is not plugged or kinked.

• Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)

• Check/Clean Drain Pump Filter of foreign objects

• Check Drain Pump

• Check Pressure Switch

• Check CCU

F/dL Door Lock Error
A Door Lock Error occurs if the door cannot be unlocked. It will try to lock it 6 times before displaying the error.

• Door Lock Mechanism broken or removed from the Door

• Check Door Lock/Switch Assembly

• Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)

• Door Lock/Switch Assembly Failure
F/dU Door Unlock Error

A Door Unlock Error occurs if the door cannot be unlocked. It will try to unlock the door 6 times before displaying the error.

• Door Lock Mechanism broken.

• Check Door Lock/Switch Assembly for foreign objects

• Check Wire Harness connections to the Door Lock/Switch

Assembly and Central Control Unit (CCU)

• Door Lock/Switch Assembly Failure

Now how about joining the Premium Services




----------------------

__________________
Coinwash.com Bulletin Board,
“We are the most used Laundromat Bulletin Board on the NET.”

Please visit the Sponsors who Support Coinwash.com


----------------------------------
Everything expressed here
is not necessarily the opinion of
Coinwash Corp. (Coinwash.com),
Sponsors, or this Webserver.
Reply With Quote
  #3  
Old 04-28-2008, 11:48 AM
Anonymous
"site-seer"
 
Posts: n/a
Default

If I can recall from my memory then e : od --> Error : Dosing or Drain--> Check pressure switch / Water level switch and its pipes and draining mechanism and its pipes.

Last edited by Anonymous; 04-29-2008 at 02:46 AM.
Reply With Quote
  #4  
Old 04-28-2008, 05:34 PM
RichRichRich RichRichRich is offline
 
Join Date: Jan 2006
Location: ny
Posts: 24
Default Swt521

I have seen this code many times on the Speed Queen SWT521 washers>

besides the water being off and the machine not draining.

check the motor and make sure it is not going off on the overload.

Good Luck
Reply With Quote
  #5  
Old 04-28-2008, 10:34 PM
Anonymous
"site-seer"
 
Posts: n/a
Default

Quote:
Originally Posted by RichRichRich View Post
I have seen this code many times on the Speed Queen SWT521 washers>
besides the water being off and the machine not draining.
check the motor and make sure it is not going off on the overload. Good Luck
Those machines have a B-Metal Overload. In case of Overload they should disconnect for a few minutes and then reconnect again. This wasn't mention in the post.
Reply With Quote
  #6  
Old 04-28-2008, 11:42 PM
Anonymous
"site-seer"
 
Posts: n/a
Default

From SQ technicians manual:
"E:0d Top Load Washer - Pressure Switch Error - Check fill adn (Misspell in the original) drain hoses for improper installation and kinks. Check fill electrical circuit. Replace inoperative switches or wires. "
I found out more than once, that their manual isn't accurate. The failure reasons may be different than the one they are mentioning.

Note:
1. I think you couldn’t find it because you were looking for ”od” but it’s “0d” (zero).
2. I’ve mailed the tech' manual to the board and I hope it will be posted in the premium forum in the next update.

Last edited by Anonymous; 04-28-2008 at 11:45 PM.
Reply With Quote
  #7  
Old 04-07-2013, 12:58 PM
phebous phebous is offline
 
Join Date: Jun 2011
Location: Sacramento, CA
Posts: 63
Default

I just got this error. It was a loose/burn connection on the back of the CPU module providing power to the motor. It is the 6pin Molex connector. If the motor does not spin, then the pump does not turn. When the pump does not turn, it will produce and Error On Drain.
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Speed Queen SC27MX Front Load Washer jfuinc Questions / Support / Repair 2 03-22-2013 03:37 AM
remove third rinse on ft load Speed Queen washer gnxsam Questions / Support / Repair 0 11-07-2007 07:42 PM


All times are GMT -5. The time now is 05:12 PM.


Powered by vBulletin® Version
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Coinwash.com has the right to cancel Memberships and to block whom ever we choose.
When we feel rules have been broken or the website (coinwash.com) has been misused.


We are an insurance agency that works exclusively with laundromat owners.